YAMAHA, Dante audio interface, TIOI-1608D

4.299,00 KM

Požurite, ostalo ih je samo 1.

The Tio1608-D is a Dante-equipped I/O rack with 16 microphone/ line inputs and 8 line outputs.


Plug In & Play Dante Stagebox Solution

The Tio1608-D is a Dante-equipped I/O rack with 16 microphone/ line inputs and 8 line outputs. Tio racks feature the same recallable D-PRE™ microphone preamplifiers as the TF series delivering extraordinarily natural and musical sound. In combination with TF series consoles, Tio racks can be connected using up to three units with a fast and easy setup.

* Optional NY64-D Card is required.

Flexible system expansion via Dante

Dante Network Audio Protocol has been adopted, not only in TF, but also in other Yamaha digital mixing consoles such as CL/QL. Combining these I/O racks and the various consoles can significantly increase the flexibility of system designs. Patching can be enabled via “Dante Controller” while Remote HA can be controlled by “R Remote” software. Audio patching and Remote HA can be controlled not only from TF but also from CL/QL.

* Please note that Remote HA of the Tio1608-D can be implemented only via the Primary port. Remote HA control of Tio1608D is not available on the secondary network, even when you are using with TF or CL/QL.

Tehničke specifikacije
Sampling frequency rate External 44.1kHz or 48kHz
Signal delay Less than 3ms INPUT to OUTPUT, connect with TF5 and NY64-D using Dante, Dante Receive Latency set to 0.25ms (one way), Fs=48kHz
Total harmonic distortion Less than 0.1% +4dBu@20Hz-20kHz into 600Ω, Gain=+66dB / Less than 0.05% +4dBU@20Hz-20kHz into 600Ω, Gain=-6dB, INPUT to OUTPUT, Fs=44.1kHz, 48kHz *Measured with a -18dB/octave filter @80kHz
Frequency response +0.5, -1.5dB 20Hz-20kHz, refer to the nominal output level @1kHz, INPUT to OUTPUT, Fs=44.1kHz or 48kHz
Dynamic range 108 dB, INPUT to OUTPUT, Gain=-6dB / 112 dB, DA Converter
Hum & noise level Equivalent input noise -128dBu, Gain=+66dB *Measured with A-weighting filter
Residual output noise -88dBu, ST master off *Measured with A-weighting filter
Crosstalk -100dB, adjacent INPUT/OUTPUT channels, Input Gain = -6dB *Measured with a -30dB/octave filter @22kHz
Heat dissipation 100-240V, 50/60Hz, 43.5kcal/h
Power requirements 100-240V, 50/60Hz
Power consumption 50W
Dimensions W 480mm (18-7/8")
H 88mm (3-4/8")
D 364mm (14-3/8")
Net weight 5.7kg (12.6lbs)
Accessories Owner’s Manual, Power Cord(2.5m), Rubber stoppers(4)
Others Temperature Range: Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃

Technical Specifications of Tio1608-D/Rio

Tio1608-D Rio3224-D Rio1608-D Ri8-D Ro8-D
Sound Philosophy Natural Sound Concept
Grade D-PRE Inherit the sublime sound of PM series -
Sampling Rate 44.1/48kHz 44.1/48/88.2/96kHz
Indicators +48V Sig, Peak, +48V Sig
Gain Compensation N/A Supported -
HA Control Redundancy from CL/QL consoles N/A (Primary only) Supported -
Controllability from R Remote software Supported
Maximum number of units using HA remotes per system Up to 3 Up to 8 -
AD8HR mode (HA control from M7CL and LS9) N/A Supported -
Analog Inputs 16 32 16 8 0
Analog Input Connector Combo Jack XLR-3-31 Type -
Analog Outputs 8 16 8 0 8
AES/EBU Outputs 0 8 (4ST) 0 0 0
AC Inlet Normal V-Lock Type
Heights 2U 5U 3U 1U 1U

Analog Input Characteristics

Input Terminals GAIN Actual Load Impedance For Use With Nominal Input Level Connector Balanced / Unbalanced
Sensitivity *1 Nominal Max. before clip
INPUT 1-16 +66dB 7.5kΩ 50-600Ω Mics & 600Ω Lines -82dBu (61.6μV) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2 or TRS phone *3) Balanced
-6dB +10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)

In these specifications, 0dBu = 0.775Vrms.
+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain.
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND

Analog Output Characteristics

Output Terminals Actual Source Impedance For Use With Nominal Output Level Connector Balanced / Unbalanced
Nominal Max. before clip
OUTPUT 1-8 75Ω 600Ω Lines +4dBu (1.23V) +24dBu (12.3V) XLR-3-32 type *1 Balanced

In these specifications, 0dBu = 0.775Vrms.
*1. 1: GND, 2: HOT, 3: COLD

Digital Input & Output Characteristics

Terminal Format Data length Level Audio Connector
Primary / Secondary Dante 24bit or 32bit 1000Base-T 16ch (Tio1608-D to other devises)
8ch (Other devises to Tio1608-D)
etherCON Cat5e

Moja košarica


Nema proizvoda u košarici.

Kreni u kupovinu!

Login & Signup